Looking for:
Troy bilt storm 2410 manual |
Troy-Bilt Snow Blower - Model 31AS62N | Troy-Bilt US.Troy-Bilt Storm 2410 Operator's Manual
Troy bilt storm 2410 manual.Troy-Bilt Operator's Manuals & Illustrated Parts Diagrams
Hide thumbs Also See for Storm : Operator's manual 60 pages , Operator's manual 31 pages , Operator's manual 60 pages. Available languages. Quick Links. Table of Contents. Previous Page. Next Page. It was the right to change product specifications, designs and carefully engineered to provide excellent performance when equipment without notice and without incurring obligation.
If applicable, the power testing information used to establish Please read this entire manual prior to operating the equipment.
Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. Page 4 Safe Handling of Gasoline Never run an engine indoors or in a poorly ventilated area.
Engine exhaust contains carbon monoxide, an odorless To avoid personal injury or property damage use extreme care and deadly gas. Gasoline is extremely flammable and the Do not operate machine while under the influence of vapors are explosive. Environmental Protection Agency EPA , Hand contact with the rotating impeller inside the discharge this product has an Average Useful Life of seven 7 years, chute is the most common cause of injury associated with snow or 60 hours of operation.
Page 6 Safety Symbols This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the machine before attempting to assemble and operate. Page 8 Chute Assembly and Directional Control Close the flange keepers to secure the chute assembly to the chute base. The flange keepers will click into place Models and when properly secure.
See Figure Remove cotter pin, wing nut and hex screw from chute NOTE: If the flange keepers will not easily click into place, control head. Install hex bolt silver indicator arrow on the pinion gear below the control previously removed, but do not secure with wing nut at panel faces upward. Page 10 Set-Up Push the chute control rod toward the control panel until the hole in the rod lines up with the hole in the chute Shear Pins control input closest to the chute control head and insert the cotter pin.
A pair of replacement auger shear pins and bow tie cotter pins NOTE: The second hole is used to achieve further are included with your snow thrower. Page 11 Tire Pressure Make certain the entire bottom surface of skid shoe is against the ground to avoid uneven wear on the skid shoes.
Equal tire pressure should be maintained at all times. Prior to operating your snow thrower, carefully read and follow all instructions below. Perform all adjustments to verify your snow thrower is operating safely and properly. Shift Lever Skid Shoes The shift lever is located in the right side of the Squeeze the control grip against the handle to engage the augers and start snow throwing action. Release to stop. Never use your hands to clear a clogged chute assembly. Shut off engine and remain behind handles until all moving parts have stopped before unclogging.
The chute clean-out tool is conveniently fastened to the rear of the auger housing with a mounting clip. The gear hex shaft should be lubricated at least once a season or after every twenty-five 25 hours of operation. Shave Plate and Skid Shoes Allow the engine to run until it is out of fuel. The shave plate and skid shoes on the bottom of the snow Carefully pivot the snow thrower up and forward so that it thrower are subject to wear. Spray lubricant inside the shaft and around the spacers and position, the cable should have very little slack.
It should NOT be the flange bearings found at either end of the shaft. Page 19 Auger Control Chute Bracket Adjustment Model Refer to the Assembly and Set-up section for instructions on If the spiral at the bottom of the chute directional control is not adjusting the auger control cable.
Page Service Service Belt Replacement Carefully pivot the snow thrower up and forward so that it rests on the auger housing. Page 21 Drive Belt Remove the belt from around the auger pulley, and slip the belt between the support bracket and the auger pulley. Page Friction Wheel Removal Friction Wheel Removal Back out the stop bolt to increase the clearance between the friction wheel disc and friction wheel.
If the snow thrower fails to drive with the drive control engaged, and performing the drive control cable adjustment fails to correct the problem, the friction wheel may need to be replaced. Perform the Drive Control test on page 18 in the See Figure Spark plug wire disconnected. Connect wire to spark plug. Fuel tank empty or stale fuel. Fill tank with clean, fresh gasoline. Page 27 Notes La a todos los modelos.
Nunca evite su funcionamiento. Page 40 Inserte la llave en el motor del motor y arranque. Consulte Para volver a ajustar el cable de control, afloje la tuerca el manual del operador del motor. Vea la Figura Suelte para que se detenga. Nunca use las manos para liberar un montaje de canal tapado.
Deje que el motor funcione hasta que se acabe el Placa de raspado y zapatas antideslizantes combustible. Page 46 Eje de la barrena Gire el soporte hacia abajo para reducir el juego del cable. Vuelva a apretar la tuerca hexagonal. Al menos una vez por temporada, quite los pasadores de cuchilla del eje de la barrena. Consulte la necesita un ajuste. This manual is also suitable for: Storm Storm Storm xp. Print page 1 Print document 56 pages.
Rename the bookmark. Delete bookmark? Cancel Delete. Delete from my manuals? Sign In OR. Don't have an account? Sign up! Restore password. Upload manual. Upload from disk. Upload from URL.
Operator's Manuals.Troy bilt storm 2410 manual
The Operator's Manual is an important part of your new outdoor power equipment. It will help you assemble, prepare, maintain and safely operate your machine. Your outdoor power equipment was built to be operated according to the rules and instructions for safe operation which are contained in the operator's manual and on the machine itself.
Read and follow all instructions in the manual before attempting to operate your outdoor power equipment. As with any type of power equipment, carelessness or error on the part of the operator can result in serious injury. Your machine is capable of amputating hands and feet and throwing objects. Failure to observe the safety rules and instructions, both on the machine and in the Operator's Manual, could result in serious injury or death.
Important: Troy-Bilt, its parents, affiliates and subsidiaries, is concerned about the safety of its customers and others. Due to the size of the Operator's Manual, some Operator's Manuals are broken down into two or more segments so that the entire Operator's Manual can be downloaded easily. Skip to Main Content. Financing Now Available for Online Purchases. Prior Year Models. Parts Manuals Diagrams. Filter By. Most Popular Parts.
Belts 6. Part Type. Reset Filters. Snow Blower Auger Belt. Item : A. Add to Cart. In Stock. Recoil Starter Assembly. Item : Item : B. Select Styles for Availability.
Snow Blower Cab. Drive Belt. Wheel Assembly, 13 x 4 x 6 Oyster. Item : A Wheel Assembly. Shear Pin Kit,.
Item : OEM Load More Products. Manuals Manuals Model. Model: 31AS62N Form Number: A. View Options: Download. Form Number: Form Number: B. Form Number: C. Form Number: E. Form Number: F.
No comments:
Post a Comment